Putting A 10-inch Two Blade Brush Cutter To The Weed Trimming Test!

That blade is made to us with an up and down motion, not side to side. The up and down movement cuts brush, vines etc into smaller pieces that you dont need to clean up. Works amazing on blackberries here in the Pacific NW

Two words: Brush. Hog. Rubber washer improv for the win!

I've used that blade also. Works amazing for brambles, and vines. Like others have said though you really wanna wear all the protection you can put on. It definitely throws some mean debris back at ya. Also a higher cc trimmer really is better for running that weighty blade. Awesome job great video!

Nice use of the o ring. Good way of improvising to keep that little spacer in place.

My favorite blade. I sharpen the bottom and sides to tackle vines and saplings! Even swamp grass flies. Mine is black with more squareed off end blades. Love that I can cut a very long swath in one tank of gas!

What an useful video again, thank you Pete. That really looks a good work to deal with. Good luck with the fight with the bush 😂

That's a badass blade with enough engine behind it. Would be literally unstoppable. I just wish they had a 12" blade exactly like that but without the curved down winglets on the tips that could eat the ground when clearing brush and very tall and thick grass.

Been using the Oregan mulching blade for a few years ,and they are fantastic! They do recommend that your trimmer us at least 30cc. I use them on my Husqvarna 535LK, and they amazing, they only cost about £12 in the UK!

I like that o-ring idea. I bought the 3-blade style from Oregon, the original designer of the mulching blades, and it's been fantastic. There are a lot of reviews of them from guys over in England, and seeing them chew through briars and brambles was good enough for me! Way better than trying to get into the thickets with a loppers and such!

I have a couple of those i used a lot during initial cleanup of my land. They worked GREAT, however I HIGHLY recommend wearing thick leather chaps, and not jokingly if I had actually still had a cup from my martial arts days, I would have worn that. This thing threw up chunks right into my upper vulnerable areas enough times that I ended up with purple welts several times that hurt quite a bit. With that said, I ended up wearing my chainsaw chaps as an extra layer to my jeans, and while it still wasn’t comfortable, It took a lot of the hit out of any wood or rocks that it may grab and throw up. I also HIGHLY recommend a hard hat with a full mesh chain saw face shield just as he does in this video. Just my advice.

i have one of these blades and love it, just use extreme caution because when you hit something like a rock, post or stump etc it sends it the blade back at your feet, it gives new meaning to kick back lol but it does a great job you can even mulch a sapling or brush by coming down it from the top

Great video.

Thanks

I bought a brush cutter attachment for my Echo PAS system. Then I bought another blade for it, which had a different size center hole. Both were Echo blades. I bought another blade adapter for the different size hole. Echo has adapters for both size holes (7/8" and 1", I think), and you wont need to rely on that reducer that comes with the Oregon blade, Of course, the rubber o-ring is cheaper. I just ordered one of these blades.

Oh yeah, they should've made the washer about as thick as the blade....

Bonjour Pete, En France ont s'en sert pour fauché les ronces ( muriers) et haute herbes assez dure( comme les chardons, rumex, etc) elle existe en 2 longueurs différentes et avec différents diamètres( pour les différentes machine). la courbe au extrémité doivent être vers le haut. c'est une lame très efficaces. mais attention elle peux être aussi dangereuse. donc ils faut impérativement porté les protection de visage, protège tibia, gants et chaussures de sécurité. PS: par contre elle s'utilise sur une débrousailleuse et non un coupe bordure! car sinon l'embrayage vas pas du tous aimé dans le temps. un coupe bordure n'as pas assez de couple et le renvoie d'angle n'est pas prévue pour cela.

Hi Pete, I may get one. Thanks, btw are you orig. from NJ?

Do they make an adapter for big stihl cutters?

Have you tried the circular saw-looking brush cutters?

👍👍