How to adjust trucks (and how NOT to)
110,075
2021-01-20に共有
How to change wheels: • How to properly change wheels on an e...
For discount deals on electric skateboards and more, visit dkwan.com/discounts/.
📦 ITEMS IN THIS VIDEO
Caliber II 184mm 44º: amzn.to/35Tfbnh
Paris V3 180mm 50º: amzn.to/39S5aZ3
Loaded Cantellated Tesseract
Landyachtz Switchblade
💚 SUPPORT THIS CHANNEL
You can support my channel in several ways. Thank you!
Buy me a drink: ko-fi.com/dkwan/
Patreon: patreon.com/dkwan/
Other ways: dkwan.com/how-to-support/
📧 CONTACT INFO
Go here: dkwan.com/contact/
🤓 DISCLAIMERS
Some of the links in this video or its description may be affiliate links, which means if you make a purchase through them, I might receive a small commission. This doesn't cost you anything and helps support the channel.
📖 TABLE OF CONTENTS
00:00 In this video
00:32 How to adjust trucks
02:48 How tight is too tight
04:14 Don't do this
04:55 Shorter kingpins
06:31 Halfs and quarters
07:02 Do it again
07:21 Rule of
コメント (21)
-
1 thread on the kingpin = 1 full turn of the kingpin nut. 3 threads = 3 full turns, etc. I thought this was obvious but based on a couple comments, seems not. Counting turns is a better way of tuning than counting threads because try measuring half a thread, or even a quarter thread…
-
As a downhill longboarder who weighs 140 pounds, I don't have a problem with tightening my trucks too much. I agree with you, though man. Honestly, if you are tightening your trucks more than two rotations, just get bushings with a harder durometer.
-
Crazy I’m watching your content from 2 years ago but man these videos have been so informative! I’m new to E skating and all of your videos have given me the knowledge and confidence to ride and maintain a board like a pro. I really appreciate you for your amazing content! Thank you!
-
Such a good, informative video! As someone who doesn’t know much about longboards but needed to loosen my trucks, I really appreciated this! 😊
-
Starting point and consistency. That's how how do mine. But I did learn when is to tight. Mine are just right. Best video on how to adjust trucks by far. On board with this method.
-
good video, I like the explenation with the consistent starting point.
-
Thank you so much for explaining this! I just got a new board and have loosened it I think a bit too much
-
As someone new to the electric board scene, i really needed this guide. I do really appreciate and realized i have tighten it incorrectly.
-
Thanks for your videos, Daniel. I just purchased a WowGo 3X (using your discount code) and before I rode it for the first time I followed your videos on how to adjust the belts, adjust the trucks, and replace the wheels (I just added bearings to the rear wheels because it shipped with only one bearing in each of the rear wheels). The board rides great and I love it. I appreciate your help. Keep up the great work!
-
I got the backfire zealot with your discount code! great channel thanks
-
Thanks for the vid, digging the Yang beanie!
-
Nice and informative video. Good for the new guys
-
Such solid advice! Really well made video 👍
-
Today is the 5th time I`m watching this video (first one was like 3 years ago) because it's the best adjusting trucks tutorial on the whole internet (at least youtube) THANK YOU <3 THANK YOU <3 THANK YOU <3 THANK YOU <3
-
Great guide on tightening trucks.
-
Thanks for the complete manual!
-
Super informative, really good content
-
Very helpful! Thank you!
-
Nice video, well explained 👍
-
Thanks, used this to help someone out.