Oversize bearing broke due to load, full overhaul due to mismatched size and re-sized.
268,941
Published 2024-05-31
#OversizeBearingBrokeDueToLoad, fulloverhaulduetomismatched size and re-sized.
#bearing #boat #agricultural #broken #completeprocess #pakistanitruck #pakistanirepair
#repair #restoration #manufactured #process
All Comments (21)
-
There was the inner and outer ring, then ball bearings were put in, it was then carried to the lathe, and magically the ball bearing spacer holder was inside too! Lol they switched to a brand new bearing when it showed it in the lathe, there was no welding marks either. Nice try, but faked!
-
Bull Shit, Things like this should be ban from being shown anywhere. You cannot repair a bearing! Period. No excuses. After 50 years as an Industrial Machine Repairman, it cannot be done, it’s like putting an egg shell back together and saying it’s as good as new. Again Bull Shit 💩
-
Присмотритесь внимательней.В конце это другой подшипник.
-
Помойму нас пытаются обмануть? Хорошая попытка, Я просто похлопаю 🤦♂️🤦♂️👏👏👏
-
Все настолько хорошо сделано, что в конце показали другой подшипник.
-
it's fake....but then so is all that Hollywood produces so it still has entertainment value. and if its not a fake then shortest bearing life ever.
-
Most of these videos are fake. If they do manage to booger weld something back together it might last 15 minutes.
-
Комментаторы чё ругаетесь? Забыли что такое индийское кино?
-
А рядом второй мастер меча и магии рессоры сваривает, чето не разу не показали как рессоры сварить это же вобще просто
-
Новые, доселе неизведанные технологии сварки подшипника, куда смотрит нобелевский комитет?
-
Токарь кстати похож на Морфиуса из "Матрицы". :D Бгггг
-
Как этот фокусник вставил сепаратор конечно большой вопрос. А чтобы подшипник лучше обрабатывался и сепаратор с шарами мягче заходили он наверное произвел отжиг😂
-
I used to believe some of these repairs but this one takes the cake
-
Видео для дураков, кто вообще ничего не понимает😂😂😂😂
-
Заварить подшипник электродом , это что-то новенькое
-
варить обойму сталистую обычным электродом ????? МОЛОДЦЫ !!!!! УСТАНОВИЛ И СРАЗУ НА ПОВТОРНЫЙ РЕМОНТ
-
Пушкин с своими сказками в гробу перевернулся 🤣
-
non sono meccanico ma, a occhio mi sembrano saldature troppo semplici su un cuscinetto che sopporta notevoli tensioni. Non viene riportato al diametro originale e la saldstura ha un mero effetto riempitivo. Il cuscinetto mostrato alla fine é diverso 😂😂 ogni segno di saldatura é sparito.
-
Hardened steel cannot be welded because it will crack again somewhere, you have to anneal it and re-heat treatment but dissimilar material is okay only if the filler is compatible, but in this application is dangerous, bearings need to be precise ground finish, at the end they just replace it with old bearing not the welded one
-
Этот бред отнял 20 минут моей жизни..... Насколько я понял изначально проблема была в том, что лопнули и внешняя и внутренняя обоймы. При этом внутренняя разошлась на пару миллиметров. А когда её сваривали, то не сжали, а варили прямо как есть. При сварке внешней обоймы не учитывали выбранную болгаркой толщину(тоже пара миллиметров) и тоже варили встык. В таком случае внешняя обойма стала меньше в диаметре, а внутренняя больше. Подшипник при этом должен был заклинить сразу. Учитывая как из сепаратора выбивали шарики молотком, а потом забивали обратно этот подшипник НЕЖИЗНЕСПОСОБЕН!!!!! И ещё..... Как в подшипнике по дороге от тисков к станку появился сепаратор??????? 🤔. Вывод: в финальной части ролика другой, новый подшипник.