IOT : Getting started with Blynk with nodemcu controlling outputs over the internet

electronic GURU
electronic GURU
14,703
0
Published 2018-06-16
Hello guys, as we know IOT is a really popular topic these days.So i thought i must make a video on that.i know i am little late for that but i can't resist to make a video on iot so guys in this video we will control output on the nodemcu over the internet using Blynk.Blynk is really easy to use app which provides control over the internet, so watch the video and have fun making your own iot projects so i hope you like the video,give me a like & share & subscribe my channel....

Thanks for watching guys....

Follow me on FB Page :-

m.facebook.com/electronicGURU001/


Affiliate Buying link :-

Nodemcu (esp8266)-

www.banggood.com/NodeMcu-Lua-WIFI-Internet-Things-…

www.banggood.com/3Pcs-NodeMcu-Lua-WIFI-Internet-Th…

www.banggood.com/Wemos-NodeMCU-V3-CP2102-Lua-WIFI-…


LED:-

www.banggood.com/100pcs-F5-5mm-White-Bright-Diode-…
www.banggood.com/100pcs-20Ma-F5-5MM-5Colors-Ultra-…

Breadboard :-
www.banggood.com/3Pcs-8_5x5_5cm-400-Tie-Points-400…

www.banggood.com/3pcs-Prototype-Board-400-Hole-Bre…

Jumper wires :-

www.banggood.com/120pcs-Multicolored-Dupont-Wire-M…
www.banggood.com/120pcs-Multicolored-Dupont-Wire-M…


Previous videos :-

Controlling RGB Led Strip with Arduino | Arduino based RGB Led strip controller

   • Controlling RGB Led Strip with Arduin...  

ESP 8266 Nodemcu ws 2812 Neopixel based LED MOOD Lamp controlled using webserver

   • ESP 8266 Nodemcu ws 2812 Neopixel bas...  

Neopixel ws 2812 LED Strip with Arduino controlled by Bluetooth from Android or iphone

   • Neopixel ws 2812 LED Strip with Ardui...  

Adafruit Neopixel 8x8 led matrix with Arduino individually addressable led matrix

   • Adafruit Neopixel 8x8 led matrix with...  

Joule Thief Lighting LED with AA battery Voltage booster LED torch from AA battery with joule thief

   • Joule Thief Lighting LED with AA batt...  

DIY Lego Blocks Quadcopter Drone | How to build a Quadcopter using DIY kit

   • DIY Lego Blocks Quadcopter Drone | Ho...  

Neopixel ws2812 LED Strip or LED Ring 12bit with Arduino Tutorial

   • Neopixel ws2812 LED Strip or LED Ring...  


DIY Power Supply | Original Hiland 0-30V 2mA 3A Adjustable DC Regulated Power Supply Module DIY Kit

   • DIY Power Supply | Original Hiland 0-...  


Arduino OLED Clock using DS1307 ic | Arduino OLED clock project

   • Arduino OLED Clock using DS1307 ic | ...  

ESP 32 Getting Started with Arduino IDE -

   • ESP 32 Getting Started with Arduino IDE  
All Comments (14)
  • @ZenoModiff
    Good Job Broii Nyz Work U Have Done ❤
  • @alfinestaa
    Itu must use USB to ttl converter for power of 8266?
  • @markengineer4084
    Hi , dont forget your resistors for the LEDs . V=vs(voltage supply)-vf(forward voltage of LED) then use V in ohms ohms law calculation . Thats why your LEDs are waaay too bright and verging on yellow
  • @bhupindersinghgill3404
    Hlo sir when i upload the program to nodemcu they show 'Blynk' was not declared in this scope. This error how to solve
  • @Padmakshi4463
    nodemcu is not getting connected to the blynk app.in serial monitor its not showing anything moreover the blynk app shows me offline should we select nodemcu or esp8266 as device ,,,when creating a project are both the same
  • @Parth_188
    Node MCU is not connecting to network what to do