ARRMA TYPHON GROM GETS CASTLES MICRO MAMBA X2 COMBO 2s, 3s or 4s ?๐คท๐พโโ๏ธ
5,490
2024-04-02ใซๅ
ฑๆ
First Typhon
castle creation micro x2 combo with the 5300kv motor.
18t Losi 2mm shaft pinion
stock spur
2ch spectrum receiver
hoovo 3s 2200mah 50c lipo batteries
Mods in the mail:
tires
shocks
esc mount plate
F/R differentials
*CVD axles when they become available..
Second Typhon mods to be installed:
57T spur, 22t pinion on stock motor
tires
shocks
Granite Grom mods to install:
2in1 6000kv specktrum motor/esc
18t pinion
2ch receiver
Stay tuned guys, thanks for watching, more vids on the way. Peace & Blessings
ใณใกใณใ (21)
-
ive used this combo but with the higher 8200 kv. I over geared it though to a 21T. It got hot but boy was it moving. You should be safe on 2s up to a 21-22T with the 5300kv! On 3S watch temp, I wouldn't bash with a 3s tho! The only thing with that 0808 motor is the 2mm shaft. I tends to snap sometimes! If that happens grab you a 380 brushless motor with a 3.175 shaft. Hot racing makes 0.5mod 3.175 pinions too! Awesome video. subbed my brotha!
-
Cool little buggy those little motors are more powerful than you think but lots of fun thx for sharing
-
Iโve done that a time or tow or three or four or more! Keep the vids coming, new sub here
-
Yo Dos nice vid ๐๐ฟ switch look big ๐
-
broken shafts on two of those. upgraded to the 1020 I believe it was with 1/8 shaft
-
Let's get it bruh
-
great setup big bro. sucka gonna fly ๐๐ผ๐๐ผ
-
Hey buddy how are you just want to make a comment i think arrma should make a slipper for the grom it would help for a number of reasons bo more stripped diffs would be a good reason ๐ฎ๐๐
-
Careful, man. The minis can get addicting real quick
-
I have the furitek kraken 6700kv on mine with a furitek speed cat, using 3s and have had zero issues.
-
i melted a 6000kv spectra firma esc motor combo. spectra receiver and transmit. used granite grom wheels. insane speed. but built up way too much heat smoked the esc and motor
-
Use the 8200 kv or new 8450kv the 8200 pulls the tires off the ground on demand on my granite grom. Arrma has a esc plate for the brushless conversion already too. You may have to trim a corner for the motor to fit though.
-
use can drill that set screw out of that pinion or cut it off with a dremel ! also you might want to invest in a vise if your gonna apply downward pressure!
-
Ez run has a 7800kv that is even smaller than that and you should be able to keep the fan
-
Were you able to fit the fan and heat sink?
-
get a micro torch for the loctite screws . Also a shorter bit length . MIP tools are truly the best!
-
what motor mount did you use, i bought the same motor and esc, the problem is the bolt holes dont line up with the the motor
-
I installed the same set up on mine after watching your video, Iโm having some issues with the motor getting super hot after 3 minutes of run time. It even melted the wires. Have you had the same issue ?
-
Maybe because I'm older and I've been doing rc cars for 20 years now but my grom is fast enough for me I just wish the car was more tunable like shock position and camber ๐๐
-
That's the correct esc but that motor is for lighter cars like the losi mini b. Castle has a motor slightly bigger I have it in my groms. 10series castle motors check it out.
