RF Module 433MHZ | Make Receiver and Transmitter from 433MHZ RF module without any microcontroller
131,413
Published 2018-07-15
Here we go, in this video i'll show you my basic rf transmitter and receiver ready to be use.
In this video you'll learn how you can send and receive data using very very cheap components!
With the help of HT12E (ENCODER) and HT12D (DECODER) IC and a pair of Rf modules of 433 Mhz.
Instructables guide link- (schmatics & explanation) : -
www.instructables.com/id/RF-Module-433MHZ-Make-Rec…
Affiliate Buying link : -
433mhz RF MODULE Buy : -
www.banggood.com/433MHz-100M-Wireless-Transceiver-…
www.banggood.com/3sets-433MHz-100M-Wireless-Transc…
www.banggood.com/433MHz-100M-Wireless-Transceiver-…
www.banggood.com/5Pcs-433Mhz-RF-Transmitter-With-R…
www.banggood.com/433Mhz-RF-Transmitter-With-Receiv…
Previous videos :-
Getting Started with ESP 8266 ESP 01 with Arduino IDE | Programming esp-01 with Arduino ide
• Getting Started with ESP 8266 ESP 01 ...
IOT : ESP 8266 Nodemcu Controlling Neopixel ws2812 LED Strip over the internet using BLYNK App
• IOT : ESP 8266 Nodemcu Controlling Ne...
IOT : ESP 8266 Nodemcu Controlling RGB LED Strip over the internet using BLYNK App
• IOT : ESP 8266 Nodemcu Controlling RG...
JLCPCB Review : How to design & order professional PCB for 2$ | PCB Designing
• JLCPCB Review : How to design & order...
IOT : Getting started with Blynk with nodemcu controlling outputs over the internet
• IOT : Getting started with Blynk with...
Controlling RGB Led Strip with Arduino | Arduino based RGB Led strip controller
• Controlling RGB Led Strip with Arduin...
ESP 8266 Nodemcu ws 2812 Neopixel based LED MOOD Lamp controlled using webserver
• ESP 8266 Nodemcu ws 2812 Neopixel bas...
Neopixel ws 2812 LED Strip with Arduino controlled by Bluetooth from Android or iphone
• Neopixel ws 2812 LED Strip with Ardui...
Adafruit Neopixel 8x8 led matrix with Arduino individually addressable led matrix
• Adafruit Neopixel 8x8 led matrix with...
Joule Thief Lighting LED with AA battery Voltage booster LED torch from AA battery with joule thief
• Joule Thief Lighting LED with AA batt...
DIY Lego Blocks Quadcopter Drone | How to build a Quadcopter using DIY kit
• DIY Lego Blocks Quadcopter Drone | Ho...
All Comments (21)
-
Thankyou so much bro. I was stuck at this part(which happens to be the underlying part of my project) for days. Finally you got me out of this !! Lots of love.
-
dude... Way cool. I found you by googling "433mhz rf transmitter and receiver module" and you where on the top returned. good stuff.
-
Many thanks for making great video... I always love your hard work .. we learn lots from you my big request plz always make this type video
-
Wonderful video! How would I connect multiple transmitters to a single receiver and have the receiver illuminate a separate led light when each individual transmitter is triggered? I'd prefer it if I didn't have to use arduino as there is very limited electricity and no wifi. Thanks!!
-
Thanks for the video, would I be able to use the receiver output (like the LEDs) with an MCU to read if a pin is high or low? Just to let everyone know from my testing it seems to have a pretty good range of at least 5ft or roughly 1.5m without the antenna, provided you are able to supply the recommend minimums to each circuit.
-
Great video, Good Explanations ,Good Job Man Keep It Up 💪
-
Good project sir It is very good option for for cost efficient project. 👌👌👌👌👌👌
-
your sharing is clear and easy understanding. Thanks for your dharing.
-
I have 2 quesions. Does the resistor on the rf reciever essentially needed? And these two Rosc resistor values needs to be exacly same values with video? What is the its importance?
-
Hello can i connect one transmitter into 2 or more receivers?? Pls cause i have an incoming project with regards to that as of now i can't see any links about that. Thanks
-
Thank you so much for the easy explanation
-
Thanks for your great Video. can I send continuous audio with this device?
-
what is the output V to the leds ? would that voltage be enough to make a cell phone vibrator work ? how can this be boosted to get 150M range if that 's possible ? Thanks for the knowledge Cheers !
-
It's very useful , thank you for teaching. Already subscribed.
-
best video ever
-
what is the range of small green rf module
-
Can use 12 volts to receiver?
-
Bla D Good! Thank you. !! Nice and simple. WiFi eat your heart out! This Lots less complicated. Nice IC Chips
-
how about a even simpler Tx to Rx set up, where : when Tx is powered up Rx has 1 pin going to +5v so I could connect a cell phone vibrator ? Could I use the same parts you selected and do that ? the range I need would be around 125 to 150meters any suggestion ? TY very much for your vids Cheers
-
thank you!!! 👌🙏👍