Abandoned Japan Brush Cutter Repairing | Shindaiwa 2401
610,758
Published 2024-01-23
- Brush Cutter Components Removal
00:13 Air filter cover
00:18 Air filter sponge
00:32 Air filter assy
00:43 Carburetor
00:55 Muffler cover
01:02 Muffler
01:17 Muffler gasket
01:36 Spark plug (BM6A)
02:06 Ignition coil brush cutter
02:15 Manifold
02:31 Starter
02:36 Starter pulley
02:56 Clutch
03:26 Flying wheel
03:40 Cylinder
03:54 Cylinder gasket
03:58 Crankcase
04:20 Crankshaft and Piston
04:25 Crankshaft bearing
05:06 Clutch house assy
05:11 Handle clamp
05:33 Gear case assy
05:57 Drive shaft
06:06 List all brush cutter parts
06:36 Fuel tank
06:50 Fuel tank cap
- Carburetor Section
12:29 Carburetor cleaning
12:52 Carburetor disassemble
13:33 Carburetor diaphragm
13:55 Carburetor gasket
14:16 Fuel pump
14:18 Carb Primer Bulb
14:36 Remaking all gaskets
- Installation Section
16:55 Crankshaft bearing installation
17:05 Crankcase assemble
17:42 Cylinder assemble
18:30 Flying wheel installation
18:38 Clutch installation
18:49 Ignition coil installation
19:20 Clutch housing installation
19:33 Starter pulley installation
19:40 Fuel tank installation
19:54 Starter installation
20:45 Carburetor installation
21:18 Spark plug installation
21:40 Muffler installation
22:14 Gear case assemble
23:10 Blade cover installation
23:21 Handle installation
25:05 Mixing oil for 2-stroke engine
26:54 Start the brush cutter
I apologize for missing the cutting test because there is not much grass this season.
I hope you find this video useful and enjoy it!
Furthermore, I am happy to receive feedback, suggestions to improve myself.
!!! I'm sorry for the mistake if I did in this video !!!
Thank you very much for choosing to watch my video!
Have a nice day
Gear Show
All Comments (21)
-
Svaka čast majstore na demonstracii Trimera
-
Love how you clean the bolts in the die
-
Great work
-
Μπράβο για την μεγάλη υπομονή σου
-
Super professional!!!
-
Very nice! A gas powered restoration! That was fun! I've always kind of wanted to do that.... but I am always waaaay too interested in just getting it running, and then using it....
-
YOU are very Professiofenal, Thanks for teaching.
-
I would rather this one than a new one
-
Very nice work as hard worker🎉
-
pro tip: dont use a ziptie to fix the crack in the tank, just melt the plastic around the tank itself with the soldering iron. fuel tanks are usualy made of HDPE or polypropylene and zipties are made of nylon, these plastics dont fuse together well and you will end up with new cracks or even having the nylon straight up peel off the tank
-
Beautiful restoration mister good job well done
-
Un trabajo espectacular. Muchas gracias por compartir, un saludo.
-
Nice job.
-
Nice work dude 😃😃
-
thank you teacher❤❤❤ Great job, thank you brother. You are so talented
-
Excelente trabalho
-
Лучший, спасибо за потраченное время!!!
-
Phenomenal video!!!!
-
Great work sir you are awesome ❤️ 😊
-
Perfect skill 👍