Linear Hall effect on E-Bike Throttle - Understanding & Testing #ebiker #ebikeThrottle #hallsensor

39,413

350 0

Published 2023-04-04

Description: In this comprehensive tutorial, we'll show you everything you need to know about e-bike throttles. From how they work to how to test and disassemble them, you'll learn all the essential information you need to diagnose and repair problems with your e-bike's throttle. Our expert instructor will guide you through the process, breaking down each step into easy-to-follow instructions. By the end of this video, you'll have the knowledge and confidence to troubleshoot and fix throttle issues on your own e-bike, saving you time and money in the long run. Whether you're a seasoned e-bike rider or just starting out, this tutorial is a must-watch for anyone looking to take their e-bike maintenance skills to the next level.

----HALL sensor SIMPLE comparison (Bipolar x Unipolar)--------------------------
   • HALL Effect Sensor Comparison - Bipol...

----LINEAR HALL Effect sensor (Analog sensor)---------
   • Linear HALL effect SENSOR 49E #hall #...

----HALL sensor TRIPLE comparison--------------------------
   • HALL EFFECT SENSOR Comparison: LINEAR...

---HALL effect experiment theory--------------------------------
   • HALL EFFECT THEORY Explained in 2.5 m...

----HALL unipolar model A3144-------------------------------------
   • HALL EFFECT SENSOR - Basics for unipo...

---Linear Hall effect on E-Bike Throttle---------------------------
   • Linear Hall effect on E-Bike Throttle...

#ebikeThrottle #hall #halleffect #hallsensor #ebike

All Comments (16)

@BCNomader 5 months ago

Thank you! Just the information I was looking for. You made my day.
@jbhawkster 5 months ago

Very well done. Thank you for this.
@vsab786 14 days ago

Thanks for the nice explanation
@anpatron4439 4 months ago

Very nice video! Very useful info about the mixing up of the wires in the connector. Do you have a vid about the way each wire is held inside the connector and how it can be released so the wires can be rearranged inside the connector?
@normanwray1341 4 months ago

Hello dear friend thank to give me your good advice off that throttle, very interesting 😅😊
@LuanaSantos-ol7vy 1 year ago

Valeu!
@Lobo-mv2ml 3 months ago

I have a Phantomgogo R1 36v scooter. The make and model are Sine wave brushless controller 2HM-0. When I tested the 5v red wire coming out of the controller I found that the 5 volt Red Wire is pushing 17.44 volts. I am afraid of connectiing the.controller to the throttle because I do not want to damage the throttle. Is this high voltage normal or is it a defect? Will it destroy my throttle?
@vijayakrishnannair 5 months ago

Nice 👍
@marvindeximo3709 6 months ago

Thank you!
@misoo83 2 months ago

Hi, i have thumb throttle that have start idle voltage 1.33v and when full run 3.42v, is this ok voltage, is this throttle ok and will this throttle work fine with such voltage values?. Thanks 🙂
@NormanWray-hi8cu 2 months ago

How could you use a baizifu conversion kit brushless kit moto sensor that as wire's red black and yellow 😊😅
@plig88luthierandelectronic63 7 months ago

If I give on the signal , more than 5 volts dc , the motor goes Above the max speed ? .. I have an urbanglide escooter and I search how to unlock the max speed ,, my scooter have 25 km/h top speed , but I don’t know where I unlocked ,, it’s from dashboard or from controller ?
@pasqualemacheda 6 months ago

nel mio acceleratore ci sono 3 fili ,BIANCO ROSSO E NERO .LA MIA BICI E UNA 250 (MARCA VIVA) SENZA LA PREDISPOSIZIONE X L'acceleratore COME LO DEVO COLLEGARE ALLA CENTRALINA .CIAO E GRAZIE SONO CONDOR 69
@richardbaynham8689 2 months ago

Cannot see anything screen too low
@sohagsowdagor2809 2 months ago

This sensor number please