How to adjust ninja ( Umarex Gauntlet ) regulator for PCP HPA Airguns (800psi to 1400psi output)
203,775
Published 2017-03-05
All Comments (21)
-
Finally the gun i paid for. Thanks again for doing this video and leaving it up to help guys like me. My Gauntlet is pushing 18s close to a grand and my regs at 1350 psi. With a little help of some Halfhill Engineering of course. No after market parts at all. That little reg held it all back because it was only putting out 800 psi. Thanks so much for this long awaited performance.Shooting so good right now and not at multi-pump speeds at K-Mart. You Rock!
-
Great videos. Really informative and I imagine I'm not the only one who's appreciative of your time.
-
your video is a big help for the airgun community, yhanks
-
Thanks for the instructional vid! Thanks to you I was able to order washers and shims, then modify my low pressure regulator to a higher output (1000psi) and my air rifle barrel responded favorably. The higher pressure got rid of my fliers, and tightened up the groups! Thanks again!
-
Thanks for sharing my man. Your videos feel like a friend filling you in. No bs intro or other crap that has nothing to do with what someone came for. It is appreciated.
-
I really appreciate your very well documented DIY videos and your hard work is noted in your details! Indy Airgunner
-
I want to thank you for all the info on the Gauntlet and how to tune it. I have a ranch in Georgia and had a rat problem because of the feed I must keep. This rifle is just great and does the job I need it for . I bought it because of your information on it and in the 6 months I own it and your advice I have never had a problem. Thank you again. Mike Babbit. Homerville, Georgia.
-
That was a great tutorial on adjusting the Ninja regs. We are also big fans of using the SCBA tanks and that is what we designed the Stikman and Cascade Man around:')
-
Very simple process once you’ve done it a few times, thanks for the educational video...
-
Thanks for the very detailed video! I just had a 1.8K burst disk blow in my new .22 Gauntlet and I really appreciated that you included them in your video! Glad I watched it all! Now if Umarex will only send me a replacement!
-
I almost bought another regulator! Thanks for the info!! Ordered all from McMaster's and excited to try this out. ;)
-
Thanks for the video .Everything is clearly explained.
-
FYI, using a factory Ninja 13 ci, 3000# tank I was getting 650fps out of a Drozd Blackbird. Altered regulator using 5 pairs of recommended Belleville washers with a single on each end and (1) 0.20” shim, velocity went to 800fps. Don’t have a pressure output gauge to measure pressure. Also noticed new ninja tank regulator has a dab of “silicone” grease on the piston rings. Not petroleum grease. Thx for the video, well done.
-
wiwww.. i'm new on using regulators and planning to buy ninja PRO V2 for my PCP air rifle... your video is very nice.. very well explained.. i learned a lot from this.. thank you :-)
-
Great video with some really good info. Very well done.
-
Stacking the belville washers in the same orientation will eliminate the spring effect of those washers then adding more shims to increase air pressure will add more working force to the four remaining pares of opposing belville washers there by increasing the potential for spring fatigue. imho
-
More power yes , for my Umarex gauntlet 22cal very interesting video, good schooling
-
Thanks for doing this video, it made it very clear.
-
Thank you for your videos. Best on you tube by a long shot building a Frankenstein pcp. I have ordered parts from the suppliers you have mention already. Have a 1322 that I want to convert over to a 2240 and ordered 2240 that I want to do a same setup as yours very well put together videos. I subscribed to your channel thank you again
-
Very informative. Thank you. You have a new subscriber. Keep the videos coming.
